Κωδικοι Σφαλματων ΒΜW - BMWForum.gr

BMWForum.gr

BMWForum.gr » Αυτοκίνητα BMW » Twin-Turbos » Κωδικοι Σφαλματων ΒΜW

Twin-Turbos Συζητησεις με ο,τι εχει να κανει με τους διτουρμπινους κινητηρες της αγαπημενης μας εταιριας

Απάντηση στο θέμα
 
Εργαλεία Θεμάτων Τρόποι εμφάνισης
03-04-09, 00:12   #1
Panoz
 
Το avatar του χρήστη Panoz
 
Status:
Εγγραφή: 27-12-2006
Ηλικία: 39
Μηνύματα: 7.932

Drives: E92 335i
Κωδικοι Σφαλματων ΒΜW

Πολυ χρησημο για οσους εχουν ή θελουν να αγορασουν διαγνωστικα
Οι κωδικοι σφαλματων ειναι Universal BMW κωδικοι και εμφανιζονται οι ιδιοι σε καθε διαγνωστικο


2F6C:
2F6C Exhaust fumeflap, input signal
Error will not cause a warning light
Error is currently present
Test conditions have been completed
Timeout
EXPLANATION: Unplugging actuator valve in trunk for added exhaust noise.
FIX: Plugging back in and clearing code.
*Code will not show up if you use the "golf tee mod"

2DEC:
2DEC Power management, battery control
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Signal or value below threshold
EXPLANATION: Disconnecting battery
FIX: Reconnect battery, clear and rescan.

2D18:
2D18 manipulation cover, maximum air mass
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption
EXPLANATION:
FIX:

2D25C:
2D25 Mass Air Flow Excessive - External Tuning Box Detected
Error will not cause a warning light
Error is currently present
Test conditions have been completed
Short circuit or signal interruption
EXPLANATION: Pretty obvious. You have an aftermarket tune.
FIX: If going to get serviced, clear, take tune out and rescan. If not than clear and don't worry about it..yet.

2D1C
2D1C Accelerator pedal module, pedal sensor signal 2
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Signal or value below threshold
EXPLANATION: Sensor in pedal not transmitting correctly.
FIX: Take to dealer

2FBF:
2FBF Fuel Pressure at Injection Release
Error will not cause a warning light
Error is currently present
Short circuit or signal interruption
EXPLANATION: Fuel flow out of the normal parameters, usual code with a tuned car.
FIX: If going to get serviced, clear, take tune out and rescan. If not than clear and don't worry about it..yet.

2DED:
2DED Power management, standby current control
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION: The closed circuit current momentarily exceeds its threshold value when the TCU wakes up to perform the "Stolen Vehicle Recovery" function. This should not cause a discharged battery.
FIX: Take to dealer.

2D5A
2D5A Control motor torque limitation
Error will not cause a warning light (it did cause a limp)
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

29DC:
29DC Cylinder injection switch-off
Error will cause a warning light
Error is not currently present
Test conditions have not been completed
Short circuit or signal interruption
EXPLANATION: HPFP failing.
FIX: Take to dealer

2DC3:
2DC3 Control clamp 15
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Timeout
EXPLANATION:
FIX:

2E8D:
2E8D Intelligent battery sensor, signal transmission
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption
EXPLANATION:
FIX:

2F8F:
2F8F Accelerator pedal module and brake pedal, plausibility
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION: Burnout
FIX: Clear

29E2:
29E2 Fuel injection rail, pressure sensor signal
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption
EXPLANATION:
FIX:

2A80:
2A80 Inlet-Vanos variable cam control test, input signal
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Timeout
EXPLANATION:
FIX:

2A85:
2A85 Outlet-VANOS variable cam control test
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Timeout
EXPLANATION:
FIX:

2D58:
2D58 DME digital motor electronics, internal failure: control nominal torque?
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Timeout
EXPLANATION:
FIX:

2EE0:
2EE0 Coolant temperature sensor, signal
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption
EXPLANATION:
FIX:

2A9A:
2A9A Camshaft sensor inlet, signal
Error will cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

2ABC:
2ABC Charging pressure sensor, electrical
Error will cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

2ABD:
2ABD Intake pressure sensor, re-running
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION: HPFP Failing?
FIX:Take care into dealer

2FBE:
2FBE Fuel pressure after motor stop
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

2AAF
2AAF Fuel Pump Plausibility
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption
EXPLANATION:
FIX:

2A17
2A17 DMTL diagnosis module tank leakage, system failure
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Timeout
EXPLANATION:
FIX:

2F0D:
2F0D Radiator blind, input signal, (GLF)

Error will not cause a warning light

Error is currently present

Test conditions have been completed

Timeout
EXPLANATION:
FIX:

30FE:
30FE Exhaust fume turbo charger, high pressure side
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION: Car went into "limp" mode. Scanned immediately.
FIX: Clear and try again. If persists take tune out and rescan. Upgrade to newest version of chip.

30FF:
30FF, Exhaust fume turbocharger low side
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:


30CF:
30CF Wastegate, input signal
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

30D0:
30D0 Wastegate 2, input signal
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

30F2:
30F2 Glow ignition: cylinder 6
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION: Super Knock in cylinder 6. Combustion knocking when running a high compressed gasoline engine with lower octane. Possible carbon buildup also.
FIX: Put good gas in your car!
*Thanks cali_guy

30F1:
30F1 Glow ignition: cylinder 5
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION: Super Knock in cylinder 5. Combustion knocking when running a high compressed gasoline engine with lower octane. Possible carbon buildup also.
FIX: Put good gas in your car!
*Thanks cali_guy

5088
Sensors gear selector switch
Error will not cause a warning light
Error is not currently present
Test conditions have not been completed
Timeout
EXPLANATION: Transmission switch did not respond in allowable time?????
FIX: Kick the shit out of the car and hope that it goes away

5DE1
DSC-ECU: ECU-internal: Clockstatus of the SP interface shows missing clock.
Error will not cause a warning light
Error is currently present
Test conditions have been completed
EXPLANATION: Codes from putting car on a dyno
FIX: Clear and rescan

5DE0
DSC-ECU: ECU-internal: Plausibility of the VASP-U_Bit versus Uz power supply_clamp_15.
Error will not cause a warning light
Error is currently present
Test conditions have been completed
EXPLANATION: Codes from putting car on a dyno
FIX: Clear and rescan

5E5B:
Stability control
Wheel speed sensor general: Long-term (several seconds) error suspicion of 3-4 RDF led to error mode.
Error will not cause a warning light
Error is not currently present
EXPLANATION: NO IDEA PLEASE HELP??? Yes I know it should have this since its on the main page.
FIX: Take to dealer?

5E40
5E40 Wheel speed sensor rear right: Signal edge missing(RDF-Typ11i).
Error will cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:
*Thanks E92White

5E1A
5E1A DSC-ECU: ECU-internal: Serial-Peripheral-Interface (SPI): Transmission failure multi IC.
Error will cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

51B0
51B0 DSC Signal not plausible: Brake pressure signal
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

A559
Clamp 30g_f cutoff
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION: Pulled fuse out behind glovebox during tune install.
FIX: Make sure fuse is inserted. Clear and rescan.

A554
Alive telephone
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

A0B0
A0B0 Ecu input brake lights
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION: Rear break bulb out.
FIX:Take to dealer to replace bulb or replace bulb on your own.
*Thanks E92White

A375
A375 Communication with airbag ECU disturbed(Error_IBUS_CONNECTION_FAIL)
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:
*Thanks E92White

A092
A092 SHD Standardization 0xA092
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:
*Thanks E92White

A3AD
A3AD CAN ID 1D0 error: Engine data
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

A3AE
A3AE CAN ID 0AA error: Idle engine speed
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

A8B6
A8B6 Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

A0B4
A0B4 Fault engine start starter
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

D356
D356 PT-CAN: Message TORQUE_3 (ID 0xAA) not received or wrong message length (DLC). [transmitter: DME]
Error will cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

D355
D355 PT-CAN: Message TORQUE_2 (ID 0x0A9) not received or wrong message length (DLC). [transmitter: DME]
Error will cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

D354
D354 PT-CAN: Message TORQUE_1 (ID 0xA8) not received or wrong message length (DLC). [transmitter: DME]
Error will cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

D904
D904 K CAN wire error
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

E717
E717 CAN message: Dates of engine
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

E71A
E71A CAN message: Torque 3
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

3100:
3100 boost-pressure control, deactivation
Error will not cause warning light
Error is not currently present
Test conditions have been completed.
EXPLANATION:

30F2:
30F2 Glow ignition: cylinder 6
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION: Super Knock in cylinder 6. Combustion knocking when running a high compressed gasoline engine with lower octane. Possible carbon buildup also.
FIX: Put good gas in your car!




--------------------------------------------------------------------------------

30F1:
30F1 Glow ignition: cylinder 5
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION: Super Knock in cylinder 5. Combustion knocking when running a high compressed gasoline engine with lower octane. Possible carbon buildup also.
FIX: Put good gas in your car!


5E5B
Wheel speed sensor general : Long-term (several seconds) error suspicion of 3-4 RDF led to error mode.
Error will not cause a warning light
Error is not currently present
Test conditions have been completed

5E40
Wheel speed sensor rear right: Signal edge missing(RDF-Typ11i).
Error will cause a warning light
Error is not currently present
Test conditions have been completed

A0B0
Ecu input brake lights
Error will not cause a warning light
Error is not currently present
Test conditions have been completed

A375
Communication with airbag ECU disturbed(Error_IBUS_CONNECTION_FAIL)
Error will not cause a warning light
Error is not currently present
Test conditions have been completed

A092
SHD Standardization 0xA092
Error will not cause a warning light
Error is not currently present
Test conditions have been completed

51B0
DSC Signal not plausible: Brake pressure signal
Error will not cause a warning light
Error is not currently present
Test conditions have been completed

3100:
3100 boost-pressure control, deactivation
Error will not cause warning light
Error is not currently present
Test conditions have been completed.

2D18:
2D18 manipulation cover, maximum air mass
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption


5DEC:
Clutch gearbox-ECU: Clutch temporarily deactivated.
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Ο χρήστης Panoz δεν είναι συνδεδεμένος  
03-04-09, 08:20   #2
konstadas
 
Εγγραφή: 28-07-2008
Ηλικία: 5
Μηνύματα: 177

Drives: N/A N/A
Μπράβο Πάνο.

Πολύ καλό.
Ο χρήστης konstadas δεν είναι συνδεδεμένος   Απάντηση με παράθεση
28-05-09, 23:53   #3
M3EST
 
Το avatar του χρήστη M3EST
 
Status: BMW Tunning & Accessories
Εγγραφή: 24-05-2008
Ηλικία: 47
Μηνύματα: 247

Drives: E82 1Μ
Πολυ χρησιμο.
__________________

www.speedandstyle.gr
210 9850450
697 9962302
Ο χρήστης M3EST δεν είναι συνδεδεμένος   Απάντηση με παράθεση
11-04-10, 04:57   #4
stratos_335i
MODERATOR
 
Το avatar του χρήστη stratos_335i
 
Status:
Εγγραφή: 18-04-2009
Περιοχή: Ελλάδα
Μηνύματα: 5.308

Drives: E46 316i
Μετρώντας απο το procede δίνει 5-ψήφιους κωδικούς όπως 10700. Μπορεί κάποιος να με βοηθήσει πως να δώ τους κωδικούς σφαλμάτων μέδω procede?
Ο χρήστης stratos_335i είναι συνδεδεμένος   Απάντηση με παράθεση
11-04-10, 10:07   #5
Panoz
 
Το avatar του χρήστη Panoz
 
Status:
Εγγραφή: 27-12-2006
Ηλικία: 39
Μηνύματα: 7.932

Drives: E92 335i
Με το computeraki των windows μετετρεψε τους σε Hexidecimal και τσεκαρε απο την ανωτερω λιστα.
__________________
Turbo Maniac...
Ο χρήστης Panoz δεν είναι συνδεδεμένος   Απάντηση με παράθεση
11-04-10, 12:40   #6
Papajim
 
Status: Banned
Εγγραφή: 24-11-2007
Περιοχή: Αθήνα
Ηλικία: 40
Μηνύματα: 2.322

Drives: E90 335i
Παράθεση:
Αρχικό μήνυμα απο stratos_335 Εμφάνιση μηνυμάτων
Μετρώντας απο το procede δίνει 5-ψήφιους κωδικούς όπως 10700. Μπορεί κάποιος να με βοηθήσει πως να δώ τους κωδικούς σφαλμάτων μέδω procede?
Μπαινεις μεσα, κλεινεις πορτα.
Βαζεις κλειδι.
Ανοιγεις προγραμμα και συνδεεις το procede online.
Πατας σταρτ (χωρις συμπλεκτη για να μην παρει μπρος).
Πατας τερμα γκαζι μεχρι να αναψει engine light
Πας στο προγραμμα και βλεπεις στο CAN DME codes τι κωδικους σου δειχνει. Αν ειναι πανω απο ενας θα τους κανει κυκλο ανα 1 δευτερολεπτο (οποτε να εχεις ενα χαρτακι να τους γραψεις).

Για να σβησεις κωδικους (γιατι αν ειναι τιποτα αντλια θα θες να τους κρατησεις για να στην αλλαξουν) απλα ξαναπατα φουλ γκαζι για 2-3 sec και βγαλε κλειδι και εισαι ετοιμος...

Οι κωδικοι που δινει το procede οπως ειπες ειναι 5ψηφια νουμερα και οχι δεκαεξαδικοι.
Αν θες τη νεοτερη λιστα ΚΑΤΕΒΑΣΕ ΑΥΤΗ ΕΔΩ!

ΥΓ. Αν εχεις τελευταια εκδοση firmware να ξερεις το procede εχει καποιο auto clear κωδικων για σφαλματα καταλυτων και tunner codes που ειναι στην ουσια αχρηστα codes και απλα θελουν σβησιμο παντα...
Ο χρήστης Papajim δεν είναι συνδεδεμένος   Απάντηση με παράθεση
11-04-10, 13:02   #7
JIMBO
 
Το avatar του χρήστη JIMBO
 
Status: O "Μυριστής Δερμάτων"
Εγγραφή: 21-03-2008
Περιοχή: Athens
Ηλικία: 49
Μηνύματα: 2.822

Drives: E93 320i
Όταν λέω ότι ο eNeRGy είναι επιστήμονας κάτι ξέρω. Νίκο μου φαίνεται έχεις επιλέξει λάθος επάγγελμα...
__________________
Opinions are like assholes, everyone's got one...
Ο χρήστης JIMBO δεν είναι συνδεδεμένος   Απάντηση με παράθεση
11-04-10, 13:32   #8
Papajim
 
Status: Banned
Εγγραφή: 24-11-2007
Περιοχή: Αθήνα
Ηλικία: 40
Μηνύματα: 2.322

Drives: E90 335i
9 Μαιου εχω συναυλια, θα σε καλεσω να μου πεις αν θα συνεχισω το cello ή οχι!!!
Ο χρήστης Papajim δεν είναι συνδεδεμένος   Απάντηση με παράθεση
11-04-10, 16:18   #9
stratos_335i
MODERATOR
 
Το avatar του χρήστη stratos_335i
 
Status:
Εγγραφή: 18-04-2009
Περιοχή: Ελλάδα
Μηνύματα: 5.308

Drives: E46 316i
Παράθεση:
Αρχικό μήνυμα απο eNeRGy Εμφάνιση μηνυμάτων
Μπαινεις μεσα, κλεινεις πορτα.
Βαζεις κλειδι.
Ανοιγεις προγραμμα και συνδεεις το procede online.
Πατας σταρτ (χωρις συμπλεκτη για να μην παρει μπρος).
Πατας τερμα γκαζι μεχρι να αναψει engine light
Πας στο προγραμμα και βλεπεις στο CAN DME codes τι κωδικους σου δειχνει. Αν ειναι πανω απο ενας θα τους κανει κυκλο ανα 1 δευτερολεπτο (οποτε να εχεις ενα χαρτακι να τους γραψεις).

Για να σβησεις κωδικους (γιατι αν ειναι τιποτα αντλια θα θες να τους κρατησεις για να στην αλλαξουν) απλα ξαναπατα φουλ γκαζι για 2-3 sec και βγαλε κλειδι και εισαι ετοιμος...

Οι κωδικοι που δινει το procede οπως ειπες ειναι 5ψηφια νουμερα και οχι δεκαεξαδικοι.
Αν θες τη νεοτερη λιστα ΚΑΤΕΒΑΣΕ ΑΥΤΗ ΕΔΩ!

ΥΓ. Αν εχεις τελευταια εκδοση firmware να ξερεις το procede εχει καποιο auto clear κωδικων για σφαλματα καταλυτων και tunner codes που ειναι στην ουσια αχρηστα codes και απλα θελουν σβησιμο παντα...
Energy respect... απλά με έσωσες.

Βάρεσα αφλογιστία στον 5 και στον 6 και έκανε σαν ξεκούρδιστο. Επίσης λάθος ένδειξη απο τον δεύτερο πίσω λάμδα επειδή έκανα την μ......α και ανέβασα πολύ το Ο2 modifier.

Λέω να ανοίξουμε ένα thread και να σχολιάζουμε τις βλάβες
Ο χρήστης stratos_335i είναι συνδεδεμένος   Απάντηση με παράθεση
12-04-10, 15:50   #10
Chiefsotos
 
Το avatar του χρήστη Chiefsotos
 
Status:
Εγγραφή: 25-07-2008
Μηνύματα: 2.254

Drives: E93 335i
Παράθεση:
Αρχικό μήνυμα απο stratos_335 Εμφάνιση μηνυμάτων
Λέω να ανοίξουμε ένα thread και να σχολιάζουμε τις βλάβες
Αντε κανε την αρχη
__________________

----------------------------------------------
Οι δρομοι ειναι πολυ επικινδυνοι απο μονοι τους.., ας φροντισουμε να οδηγουμε με χαμηλες ταχυτητες και τα ματια ανοιχτα!!!
Ο χρήστης Chiefsotos δεν είναι συνδεδεμένος   Απάντηση με παράθεση
Απάντηση στο θέμα

Tags
bavarian, λαμπακι, κωδικοι, σφαλμα, technics

Εργαλεία Θεμάτων
Τρόποι εμφάνισης

Δικαιώματα - Επιλογές
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is σε λειτουργία
Τα Smilies είναι σε λειτουργία
Ο κώδικας [IMG] είναι σε λειτουργία
Ο κώδικας HTML είναι εκτός λειτουργίας

Forum Jump